If you purchase this report now and we update it in next 100 days, get it free!
The global emergency lightinginverter market is shaped by life-safety regulations and certification requirements. An inverter must demonstrate that it can detect a normal power supply failure, transfer to battery power within a specified time, maintain the emergency load for the required duration, and recharge the battery within the prescribed period. These requirements are established through different safety standards and regional regulations. In Europe, EN 50171:2021 governs central safety power supply systems. Its 2021 edition introduced a new clause covering test systems, added requirements for inverters and converters, defined maximum superimposed alternating currents for battery chargers, and updated the scope and normative references. The 2022 corrigendum is incorporated into the current text. EN 50171 distinguishes between Central Power Supply Systems (CPS) and Low Power Supply Systems (LPS). CPS systems operate without an output power limitation, while LPS systems are limited to 1,500 W for one hour or 500 W for three hours. The standard also requires the inverter to clear a final-circuit fault and continue operating without tripping its own protective device. This requirement distinguishes emergency lighting inverters from general-purpose UPS systems. In North America, UL 924 establishes safety requirements for emergency lighting and power equipment. Its scope includes central station battery banks, inverters, and automatic battery charging and control equipment. The 2023 edition became effective in October 2024 and introduced revised requirements for the equipment covered by the standard.
NFPA 101 requires emergency illumination for at least 90 minutes, with transfer to battery power within 10 seconds. New systems supplying emergency lighting are classified at least as Type 10, Class 1.5, Level 1, meaning the inverter must come online within 10 seconds and sustain the emergency load for 90 minutes. Testing requirements are also important. NFPA 101 specifies a 30-second functional test at least once every 30 days and an annual test demonstrating the full 90-minute duration. Computer-based self-testing and self-diagnostic systems may be used as alternatives to manual testing. IEC 62034:2012 provides the performance and safety framework for automatic test systems, including functional and duration tests, monitoring of timing circuits, and detection of communication, component, and software failures. Automatic testing and monitoring are therefore important certified functions rather than optional convenience features. Regional battery requirements further influence product design and market access. China's GB 17945-2024, effective from 1 May 2025, prohibits cobalt lithium, nickel-cobalt-manganese lithium, and other cobalt-containing lithium-ion chemistries in fire emergency lighting and evacuation indication systems. Lithium iron phosphate is permitted. The standard also limits the rated capacity of lithium-ion central power supplies to 0.5 kWh and lead-acid, nickel-cadmium, or nickel-metal-hydride central power supplies to 5 kWh. These restrictions aim to reduce thermal-runaway risks.
What's Inside a Bonafide Research`s industry report?
A Bonafide Research industry report provides in-depth market analysis, trends, competitive insights, and strategic recommendations to help businesses make informed decisions.
Saudi Arabia requires emergency lighting to comply with SASO 2920 and provide at least 90 minutes of operation. Products must be registered on the SABER platform and obtain an IECEE Recognition Certificate covering safety and electromagnetic compatibility before customs clearance. Emergency lighting is exempt from the energy-efficiency registration applicable to general lighting. The EU Battery Regulation 2023/1542 also affects industrial batteries used in emergency lighting inverters. From 18 August 2031, recycled-content thresholds apply to cobalt (16 percent), lead (85 percent), lithium (6 percent), and nickel (6 percent). Manufacturers must therefore document battery-cell provenance and recycled content in addition to demonstrating electrical performance. Certification is the first major competitive filter. A central inverter intended for a European hospital must meet EN 50171:2021 requirements, including the relevant CPS or LPS classification, final-circuit fault-clearing capability, and battery recharge requirements. The specified recharge performance includes reaching 80 percent capacity within 12 hours, alongside the 24-hour recharge requirement. Products must also meet the applicable CE marking requirements under the EMC and Low Voltage Directives. In North America, the same product requires UL 924 listing. Where it supplies emergency egress lighting, it must carry the appropriate UL listing under the applicable local lighting code. The revised requirements in the 2023 edition apply from October 2024. Suppliers targeting China must comply with GB 17945-2024 battery chemistry restrictions and capacity limits. This makes battery selection a market-specific requirement rather than a decision based only on performance or cost.
The choice between central and distributed inverter architectures is another source of differentiation. Central inverters concentrate batteries and power electronics in one location. They can provide transfer times below 2 milliseconds in no-break models, simplify maintenance through installation in a conditioned room, and reduce cost per fixture in large projects. They also provide a single testing point, allowing monthly 30-second and annual 90-minute tests to be automated and recorded in a downloadable audit log. Distributed inverters place smaller units near individual circuits or luminaires. They are suitable for phased renovations and buildings with scattered wings where installing new homeruns is costly. Their main advantage is failure isolation, as a failure generally affects only the relevant zone. They also provide instant relighting for normally-off luminaires. However, they create a higher long-term maintenance burden because every unit has its own battery. Automatic testing and monitoring provide another competitive advantage. IEC 62034 and NFPA 101 create recurring testing obligations, and manual testing can increase maintenance costs. Central inverters with integrated automatic testing and data logging can reduce the need for technicians to visit individual fixtures while providing evidence for compliance audits.
Market DynamicsDriver: Safety standards and testing obligations creating a replacement market • Emergency lighting regulations create recurring demand for compliant inverter systems across large commercial, institutional, and public facilities. EN 50171:2021 requires central power supplies to be dedicated to essential safety equipment, clear final-circuit faults without tripping their own protective devices, and recharge batteries within the specified period. Facilities with large emergency loads that exceed the LPS limits must consider CPS systems rather than relying on individual low-power units. • NFPA 101 also establishes a 90-minute emergency duration, a 10-second transfer requirement, and recurring monthly and annual testing obligations. IEC 62034 automatic test systems can reduce the labour involved in these tests by automating the process and recording results without requiring technicians to visit every luminaire. • Central inverter systems are particularly attractive in large facilities where individual battery replacement and access-equipment costs can be significant. Their batteries have a design life of 10 to 25 years, compared with the 3-to-5-year service life of self-contained luminaire batteries. This difference can improve the total cost of ownership of central systems in large installations.
Make this report your own
Have queries/questions regarding a report
Take advantage of intelligence tailored to your business objective
Reecha Roy
Research Analyst
Challenge: Battery chemistry restrictions and underutilisation of monitoring data • Different regional battery requirements create a challenge for manufacturers seeking to sell the same inverter platform across multiple markets. China's GB 17945-2024 prohibits cobalt-containing lithium chemistries and limits lithium central power supplies to 0.5 kWh. Meanwhile, the EU Battery Regulation 2023/1542 introduces recycled-content requirements for lead and lithium, among other materials, from 2031. Manufacturers may therefore need different battery configurations and additional certification for different markets. • Another challenge is the underutilisation of monitoring data. Automatic test systems generate information about inverter operation and battery performance, but facility operators may not integrate this information into their maintenance processes. • The UK National Highways Central Management System contract for street lighting explicitly states that the system is not being used to its full potential and requires optimisation to deliver the intended benefits of dimming, remote monitoring, and reduced roadside visits. A similar issue can arise in emergency lighting: an inverter with data logging may fail to deliver its full compliance and labour-saving benefits if its monitoring information is not integrated into the facility's maintenance workflow.
Trend: Automatic testing and battery compliance becoming key product differentiators • Emergency lighting inverters are increasingly moving from passive standby systems towards monitored assets with automatic testing capabilities. IEC 62034:2012 provides the framework for these automatic test systems, while integrated central inverter testing can support NFPA 101's monthly and annual testing obligations. • These systems can generate downloadable test logs for review by the authority having jurisdiction, reducing dependence on manual inspection and providing evidence of system performance. • Battery compliance is also becoming more important. China's GB 17945-2024 capacity limits and chemistry restrictions, together with the EU Battery Regulation's recycled-content thresholds, make battery provenance and material composition important parts of product documentation. • As a result, competitive differentiation is increasingly based on the ability to demonstrate test results, battery provenance, and chemistry compliance through a complete evidence package, rather than on output waveform and transfer time alone.
Segmentation AnalysisBy Inverter Type • Central Emergency Lighting Inverters are designed for large facilities requiring a centralised emergency power supply. They provide fast transfer, centralised maintenance, lower cost per fixture in large projects, and a single testing point for automated compliance checks. Under EN 50171:2021, CPS systems have no output power limitation and are suitable for loads exceeding the LPS limits of 1,500 W for one hour or 500 W for three hours. • Distributed Emergency Lighting Inverters place smaller units at circuit or luminaire level. They are suitable for phased renovations, scattered building wings, outpatient facilities, and mobile units where installing new homeruns is costly. They isolate failures to individual zones or fixtures but require more maintenance because each unit has its own battery. • The two architectures differ in cost and failure exposure. A central inverter failure can affect the entire emergency circuit, while distributed systems limit the impact to the affected zone or fixture. The choice therefore depends on both capital cost and the facility's approach to operational risk.
Don't pay for what you don't need. Save 30%
Customise your report by selecting specific countries or regions
By Output Type • AC Output inverters are the dominant configuration because they supply standard 230 V or 400 V AC emergency luminaires through the building's normal distribution boards. This allows a wide range of luminaires to be used without requiring a separate DC-rated lighting population. Static inverter systems typically provide continuous 230 V single-phase or 400 V three-phase AC output. • DC Output inverters supply luminaires with control gear designed for DC operation. They are used where the lighting population is specified for DC supply and distribution losses are acceptable over the cable run. However, they restrict fixture selection to DC-compatible products and are less common than AC output systems.
By Power Rating • Low Power inverters, typically within the LPS limits, serve small commercial buildings and individual floors where distributed systems may be preferred. They follow the relevant EN 50171 requirements, with the LPS output limitation determining their capacity. • Medium Power inverters serve mid-rise commercial and institutional buildings where emergency loads exceed the LPS limits but can still be supplied economically by a single CPS installation. • High Power inverters serve hospitals, high-rise buildings, transportation infrastructure, and large industrial facilities. Their emergency loads may include egress lighting, fire safety systems, and other critical infrastructure. EN 50171 requires central supplies to be dedicated to essential safety equipment, making it important to separate safety loads from general building loads when calculating capacity.
By Battery Compatibility • Lead-Acid Compatible inverters remain an established configuration because the chemistry is well understood and recycling infrastructure is mature. The EU Battery Regulation's 85 percent recycled-lead threshold from 2031 is supported by existing secondary lead supply. The recycling-efficiency target for lead-acid batteries is 75 percent by the end of 2025. • Lithium-Ion Compatible inverters are gaining attention because lithium iron phosphate offers longer cycle life and lower maintenance than lead-acid batteries. However, China's GB 17945-2024 restricts cobalt-containing lithium chemistries and limits lithium central power supplies to 0.5 kWh. Lithium use in China is therefore limited to permitted chemistries and capacity levels. • Nickel-Cadmium Compatible inverters retain a niche in high-temperature and high-reliability applications. • Multi-Chemistry Compatible inverters are designed to support different battery types and serve multiple markets. However, compatibility claims must be supported by battery-level certification and evidence rather than relying only on the inverter's charger specifications.
By Application • Commercial Buildings represent a major application segment because offices, retail facilities, and hospitality buildings require emergency lighting for safe evacuation. The choice between central and distributed inverters depends on building size, luminaire accessibility, and local emergency-duration requirements. • Industrial Facilities use central inverters where high-mounted luminaires make individual battery maintenance expensive. The longer battery design life of central systems can provide an advantage in warehouses and manufacturing environments where access equipment and maintenance visits add to operating costs. • Healthcare Facilities have demanding emergency power requirements. Hospitals must maintain emergency lighting during generator testing and power transfers. No-break central inverters with transfer times below 2 milliseconds are specified for operating rooms and intensive care units where interruptions are unacceptable. These installations must also account for NFPA 99 essential electrical system requirements and NEC Article 517 provisions for separate automatic-transfer switches for each branch. • Transportation Infrastructure and Public Buildings use central inverters where emergency loads are large and reliability requirements are high. Public procurement in these segments can also introduce additional certification and domestic-content requirements.
Regional Analysis • Europe operates under EN 50171:2021 for central safety power supply systems. Its CPS and LPS classifications determine output-power limits, while the standard also covers final-circuit fault clearing, battery recharge to 80 percent within 12 hours, and the requirement for supplies to be dedicated to essential safety equipment. EN 60598-2-22 applies to emergency luminaires, while IEC 62034:2012 provides the framework for automatic test systems. The 2021 edition of EN 50171 introduced a new test-systems clause, added requirements for inverters and converters, and established limits for superimposed alternating currents in battery chargers. The May 2022 corrigendum is incorporated into the current text. The EU Battery Regulation 2023/1542 also applies to industrial batteries used in inverters. It establishes recycled-content thresholds from 18 August 2031 and recycling-efficiency targets from the end of 2025. • North America follows UL 924 for emergency lighting and power equipment, including inverters and automatic battery charging and control equipment. The 2023 edition became effective in October 2024. NFPA 101 requires emergency lighting to operate for at least 90 minutes, with transfer to battery power within 10 seconds. It also establishes monthly 30-second functional tests and annual 90-minute duration tests, supporting demand for automatic testing and monitoring capabilities. • China's GB 17945-2024, effective from 1 May 2025, prohibits cobalt-containing lithium chemistries in fire emergency lighting and evacuation indication systems while permitting lithium iron phosphate. The standard limits lithium-ion central power supplies to 0.5 kWh and lead-acid, nickel-cadmium, or nickel-metal-hydride central power supplies to 5 kWh. These requirements influence battery selection and inverter configuration for products sold in the country. • India's emergency lighting inverter market is shaped by the BIS framework and the National Lighting Code Part 9. IS 10322 (Part 5/Sec 8) applies to emergency luminaires, while BIS certification is required for the electrical portion of the installation. • Saudi Arabia requires emergency lighting to comply with SASO 2920 and provide at least 90 minutes of operation. Products must be registered on the SABER platform and supported by an IECEE Recognition Certificate for safety and electromagnetic compatibility. Emergency lighting is exempt from the energy-efficiency registration applicable to general lighting. The Saudi Building Code SBC 1008.3.4 also specifies a 90-minute duration and an illuminance reduction requirement from 11 lux to 6 lux for new buildings.
Considered in this report • Historic Year: 2020 • Base year: 2025 • Estimated year: 2026 • Forecast year: 2031
Aspects covered in this report • Global Emergency Lighting Inverters Market with its value and forecast along with its segments • Various drivers and challenges • On-going trends and developments • Top profiled companies • Strategic recommendation
By Inverter Type • Central Emergency Lighting Inverters • Distributed Emergency Lighting Inverters
By Output Type • AC Output • DC Output
By Power Rating • Low Power • Medium Power • High Power
By Application • Commercial Buildings • Industrial Facilities • Healthcare Facilities • Transportation Infrastructure • Public Buildings
Request Table of Contents
Emergency Lighting Inverters Market Research FAQs
Key driver: Safety standards and testing obligations creating a replacement market. Key challenge: Battery chemistry restrictions and underutilisation of monitoring data. Key trend: Automatic testing and battery compliance becoming key product differentiators.
The report uses 2020 as the historic year, 2025 as the base year, 2026 as the estimated year, with forecasts up to 2031.
The Global Emergency Lighting Inverters Market is analysed by inverter type (Central Emergency Lighting Inverters, Distributed Emergency Lighting Inverters); output type (AC Output, DC Output); power rating (Low Power, Medium Power, High Power); battery compatibility (Lead-Acid Compatible, Lithium-Ion Compatible, Nickel-Cadmium Compatible, Multi-Chemistry Compatible); application (Commercial Buildings, Industrial Facilities, Healthcare Facilities, Transportation Infrastructure, Public Buildings).
The report covers Global.
This report is open for pre-booking. Pre-book it to receive the full report as soon as it is released. You can also request a free sample and the table of contents in the meantime.
Yes. Bonafide Research can add countries, segments or company profiles to match your requirements. Request customisation.
One individual can access, store, display, or archive the report in Excel format but cannot print, copy, or share it. Use is confidential and internal only. License information
One individual can access, store, display, or archive the report in PDF format but cannot print, copy, or share it. Use is confidential and internal only. License information
Up to 10 employees in one region can store, display, duplicate, and archive the report for internal use. Use is confidential and printable. License information
All employees globally can access, print, copy, and cite data externally (with attribution to Bonafide Research). License information