If you purchase this report now and we update it in next 100 days, get it free!
The daylight sensor market is best understood as a building-code accessory market in which the sensor’s commercial value is determined less by its sensing element than by the control sequence it enables and the code compliance it documents. ASHRAE 90.1-2025 expands daylight-responsive controls by requiring dimming or shutoff near windows and skylights, mandates more granular zoning that groups luminaires with occupancy and daylight sensors, and tightens automatic shutoff provisions with clearer guidance on sensor placement and overrides. The 2024 International Energy Conservation Code requires continuous dimming down to 10 percent of full power with full shutoff capability, and it extends automatic shutoff to nearly all luminaires and switched receptacles. California’s Title 24 2025 update, effective for permits from 1 January 2026, lowered the daylight-responsive control threshold to 75 watts of general lighting in any primary sidelit, secondary sidelit, or skylit daylit zone, requires photosensors in each zone positioned so they are not readily accessible to unauthorised personnel, and mandates continuous dimming in zones with multilevel lighting controls. The European Union’s revised Energy Performance of Buildings Directive 2024 makes automatic lighting controls part of the Building Automation and Control Systems obligations for non-residential buildings, with requirements phasing in by 2028 for buildings with heating or cooling capacity above 290 kilowatts and by 2029 for buildings above 70 kilowatts, and the controls must be suitably zoned and capable of occupancy detection.
Lutron’s Vive system supports wireless daylight sensing and control through the LRF2-DCRB wireless daylight sensor, which is positioned as the solution for code-compliant daylight harvesting and provides flexible sensor placement, and Lutron’s Radio Power Savr LRFX-DCRB wireless daylight sensor is calibrated across a light range of 0 to 107,000 lux with FCC, IC, and international certifications. Signify’s Philips MasterConnect sensors provide motion and daylight sensing that enables fixtures to qualify for Controls Category 6 towards DLC V6.0 Premium certification, and the MasterConnect sensors are listed under the DLC identifier NMUQ3AA2K6E, with daylight regulation configurable through the MasterConnect app rather than fixed at a factory-set lux level. Leviton’s GreenMAX DRC system incorporates occupancy and daylight sensing directly into the room controller architecture, and the GreenMAX DRC Digital Sensor monitors ambient light levels and dims lighting accordingly, with the system listed on the DLC Qualified Products List when used as part of a GreenMAX DRC system. Legrand’s Wattstopper DLM wireless open-loop photosensor LMDL-600 measures the daylight contribution to automatically switch or dim multiple zones of lighting, and Legrand’s DALI corridor sensors combine a presence sensor with a daylight sensor that measures natural and artificial light to control lighting according to the desired setpoint. Hubbell’s Load Logic RoomController daylight sensor continuously measures daylight levels and sends the information to the controller unit over standard UTP patchcords, and Hubbell’s NX Lighting Control platform supports wireless programming of daylight sensor settings including upward or downward orientation selection. Schneider Electric’s ceiling-mounted Daylighting Sensor provides on, off, and 0–10 volt continuous dimming functions in accordance with available natural light, and its KNX brightness and temperature sensor MTN663991 serves outdoor and façade applications within the same control ecosystem.
What's Inside a Bonafide Research`s industry report?
A Bonafide Research industry report provides in-depth market analysis, trends, competitive insights, and strategic recommendations to help businesses make informed decisions.
Market DynamicsDriver: Building codes converting daylight response from an efficiency option into a permit condition Building energy codes have made daylight-responsive controls a condition of permit approval and rebate eligibility, and this is the most reliable demand signal in the category because it applies to new construction and major alterations regardless of occupant preference. ASHRAE 90.1-2025 expands daylight-responsive controls by requiring dimming or shutoff near windows and skylights and mandates more granular zoning that pairs luminaires with occupancy and daylight sensors. Title 24 2025 lowered the threshold to 75 watts of general lighting in any daylit zone, effective for permits from 1 January 2026, which brings a larger share of small and medium commercial spaces into the requirement than the prior code did. The EU EPBD 2024 requires automatic lighting controls with occupancy detection in non-residential buildings above 290 kilowatts by 2028 and above 70 kilowatts by 2029, and it treats lighting controls as part of the Building Automation and Control Systems obligations rather than a standalone measure. A General Services Administration study conducted by Lawrence Berkeley National Laboratory across five federal buildings found an average annual energy savings of 27 percent from daylight harvesting, with simple payback as low as four years, which gives building owners a documented financial basis alongside the compliance obligation.
Challenge: Commissioning burden and sensor placement failures undermining claimed savings The principal constraint on daylight sensor market conversion is not sensor cost but commissioning quality, because a photosensor that is incorrectly placed, improperly calibrated, or affected by uncontrolled local conditions will fail to deliver the savings that justify the installation. Open-loop sensors avoid feedback instability but can be defeated by window shades and changing surface reflectance, while closed-loop sensors compensate for those conditions but require commissioning to stabilise the feedback loop and are sensitive to sensor placement relative to the controlled luminaires. Title 24 requires photosensors to be installed in each daylit zone and positioned so they are not readily accessible to unauthorised personnel, which means that placement is a code requirement rather than an installer preference, and the same code requires continuous dimming in zones with multilevel controls rather than stepped response. The EU EPBD requires automatic lighting controls to be suitably zoned and capable of occupancy detection, which adds a zoning and addressing burden that standalone photocells cannot satisfy without integration into a networked control system. The practical effect is that the sensor’s value is realised only when it is specified as part of a commissioned control sequence, and sensors sold as isolated components frequently underperform the savings documented in laboratory and government field studies.
Trend: Networked lighting controls absorbing standalone sensors into addressable zone architecture Daylight sensors are migrating from standalone photocells and fixture-mounted devices into networked lighting control systems where the sensor is an addressable node reporting to a zone controller rather than a direct switching device. The DLC’s Networked Lighting Controls Qualified Products List recognises products with integral daylight or photocell sensor function as part of a networked control system, and utility programmes distinguish between fixture-mounted daylight sensors and networked lighting controls with high-end trim and networking capabilities. Lutron’s Vive system uses wireless daylight sensors that communicate with the control system rather than wiring directly to a luminaire, Signify’s MasterConnect sensors are commissioned and configured through a Bluetooth app rather than fixed at the factory, and Leviton’s GreenMAX DRC Digital Sensor operates as a node within the room controller architecture. This trend aligns with the occupancy-sensing and continuous-dimming mandates in ASHRAE 90.1-2025 and the EPBD because networked controls provide the zoning, addressing, and reporting infrastructure that those codes assume, and it raises the competitive value of integration capability relative to sensing element manufacturing.
Make this report your own
Have queries/questions regarding a report
Take advantage of intelligence tailored to your business objective
Reecha Roy
Research Analyst
Segmentation AnalysisBy Sensor Type • Photodiode sensors offer linear response across a wide illuminance range and are suited to closed-loop daylight harvesting where the sensor must measure both daylight and electric light without saturation, though the output typically requires amplification before it can be used by a controller. • Phototransistor sensors provide a higher output signal that may not require amplification and are commonly used in open-loop and switching applications where the control sequence is on/off or stepped rather than continuous dimming. • Photocell sensors, including light-dependent resistor types, are widely used in outdoor dusk-to-dawn switching and in simple indoor daylight shutoff applications, and they are the sensing element most commonly associated with standalone photocell switches certified to EN 60669-2-1. • Digital light sensors integrate the sensing element with signal processing and a communication interface, allowing the sensor to report lux values or calibrated illuminance to a networked controller rather than acting as a direct switching device, and this category is growing as the DLC Networked Lighting Controls framework and the EPBD BACS requirements push sensors into addressable control architectures.
By Technology Analog sensors produce a continuous voltage or current proportional to illuminance and are used in open-loop and closed-loop control circuits where the controller performs the comparison against a setpoint, and they are the simpler and lower-cost option for standalone daylight switching. Digital sensors convert the measured illuminance into a digital value and transmit it over a bus or wireless protocol, which allows calibration, zoning, and reporting functions that analog sensors cannot support without additional hardware, and the DLC’s Networked Lighting Controls listing and the EPBD’s interoperability requirements favour digital architectures because they can be integrated into building automation systems alongside occupancy and other sensor data.
By Control Type • Open-loop control uses a photosensor positioned to detect daylight only, without feedback from the artificial light being controlled, which makes the sensor insensitive to lamp depreciation and local surface changes but dependent on accurate commissioning of the relationship between measured daylight and required electric light output. • Closed-loop control uses a photosensor that detects both daylight and the artificial light produced by the controlled system, which allows the controller to compensate for lamp lumen depreciation and changing room conditions but requires a feedback-stable control algorithm and careful commissioning to avoid oscillation.
Don't pay for what you don't need. Save 30%
Customise your report by selecting specific countries or regions
By Application • Commercial buildings represent the largest application pool because offices, retail, and mixed-use interiors combine large daylit perimeter zones with code-mandated lighting controls, and the ASHRAE 90.1-2025 and Title 24 requirements are written primarily around these space types, with the GSA/LBNL study demonstrating 27 percent average savings in federal office buildings. • Residential buildings use daylight sensors less intensively for general lighting but increasingly for outdoor dusk-to-dawn switching and for common-area lighting in multi-family buildings, where photocell switches certified to EN 60669-2-1 provide a low-cost compliance path. • Industrial facilities use daylight sensors in warehouses and production areas where skylights and high-bay lighting create a strong daylight-harvesting business case, and the 2024 IECC’s expansion of occupancy-sensing requirements to warehouses and data centres indicates that the code framework is moving toward broader industrial coverage. • Outdoor lighting applications use photocell sensors for street lighting, parking area lighting, and façade lighting where dusk-to-dawn switching is the primary requirement, and Australia’s NCC Specification 40 requires daylight sensors and dynamic lighting control devices to respond across a 50 to 1,000 lux range and to dim continuously or step down to 50 percent of full power for applicable lighting.
By Distribution Channel • Direct sales dominate specification-grade commercial and institutional projects because the daylight sensor must be selected as part of a lighting control sequence, commissioned against the daylit zone layout, and documented for code compliance, and these activities require engagement between the controls manufacturer, the lighting designer, and the commissioning agent. • Indirect sales through electrical wholesalers and lighting distributors serve replacement, small retrofit, and maintenance demand, and the wholesaler’s ability to confirm DLC listing, EN 60669-2-1 certification, or code-specific compatibility at the counter determines the transaction.
Regional Analysis • North America operates under ASHRAE 90.1-2025, which requires continuous dimming to 10 percent with full shutoff and expanded daylight-responsive controls near windows and skylights, and under California Title 24 2025, which lowered the daylight-responsive threshold to 75 watts in any daylit zone and requires photosensors in each zone with continuous dimming where multilevel controls are present. • Europe applies the revised EPBD 2024, which requires automatic lighting controls with occupancy detection as part of BACS obligations for non-residential buildings above 290 kilowatts by 2028 and above 70 kilowatts by 2029, alongside EN 60669-2-1 as the product safety standard for the sensor or photocell switch itself. • Asia-Pacific combines China’s GB 55015-2021, which requires partitioned and grouped lighting control in daylit areas with automatic adjustment according to daylight conditions, and GB/T 50034-2024, which specifies that places with available daylight should automatically adjust illuminance in response to changes in natural light, alongside India’s Energy Conservation Building Code, which requires photo-sensor control in daylight areas and permits a 20 percent lighting power density adjustment factor for spaces with more than 70 percent of their area under daylight controls. Australia’s NCC Specification 40 requires daylight sensors and dynamic lighting control devices to respond across 50 to 1,000 lux and to dim continuously or step to 50 percent, with specific requirements for car park entry zones and perimeter lighting. • South America is shaped by Brazil’s INMETRO INI-C Normative Instruction, which incorporates daylight contribution and local internal control criteria into building energy efficiency assessment under INMETRO Ordinance No. 309/2022, creating a conformity framework that rewards documented daylight-responsive controls. • Middle East and Africa, particularly the Gulf, combines Saudi Arabia’s SASO 2902:2018 framework for lighting products with active smart-building specifications, and the UAE requires ECAS certification for LED products alongside daylight sensors and occupancy controls for Estidama and Al Sa’fat credit compliance, making certification and rating-system documentation the gating criteria for specification in the region.
Considered in this report • Historic Year: 2020 • Base year: 2025 • Estimated year: 2026 • Forecast year: 2031
Aspects covered in this report • Global Daylight Sensor Market with its value and forecast along with its segments • Various drivers and challenges • On-going trends and developments • Top profiled companies • Strategic recommendation
By Sensor Type • Photodiode Sensors • Phototransistor Sensors • Photocell Sensors • Digital Light Sensors
By Technology • Analog • Digital
By Control Type • Open-Loop Control • Closed-Loop Control
By Distribution Channel • Direct Sales • Indirect Sales
Request Table of Contents
Daylight Sensor Market Research FAQs
Key driver: Building codes converting daylight response from an efficiency option into a permit condition. Key challenge: Commissioning burden and sensor placement failures undermining claimed savings. Key trend: Networked lighting controls absorbing standalone sensors into addressable zone architecture.
The report uses 2020 as the historic year, 2025 as the base year, 2026 as the estimated year, with forecasts up to 2031.
The Global Daylight Sensor Market is analysed by sensor type (Photodiode Sensors, Phototransistor Sensors, Photocell Sensors, Digital Light Sensors); technology (Analog, Digital); control type (Open-Loop Control, Closed-Loop Control); application (Commercial Buildings, Residential Buildings, Industrial Facilities, Outdoor Lighting); distribution channel (Direct Sales, Indirect Sales).
The report covers Global.
This report is open for pre-booking. Pre-book it to receive the full report as soon as it is released. You can also request a free sample and the table of contents in the meantime.
Yes. Bonafide Research can add countries, segments or company profiles to match your requirements. Request customisation.
One individual can access, store, display, or archive the report in Excel format but cannot print, copy, or share it. Use is confidential and internal only. License information
One individual can access, store, display, or archive the report in PDF format but cannot print, copy, or share it. Use is confidential and internal only. License information
Up to 10 employees in one region can store, display, duplicate, and archive the report for internal use. Use is confidential and printable. License information
All employees globally can access, print, copy, and cite data externally (with attribution to Bonafide Research). License information